20241030-1246 - add support for Singapore region 20240822-1637 - increase GPS reception performance/quicker fix, by optimizing Bluetooth transmissions when the DroneBeacon has not a GPX fix. - use hardware functions to generate random MAC address used in Bluetooth/WLAN transmissions. 20240501-1330 - bug fix use current time in the system message and not the take-off time - prevent non-compliant settings for the USA region: only allow Bluetooth dual-mode and WLAN Beacon in the configuration menu. 20240116-1645 - added a secondary ID that will be included in the Remote ID signal. This is needed in the EU (for business clients). 20240106-1158 - added a button 'to factory defaults' to set all parameters to default values - improved description/explanation for the EU operator ID (OPRN) input box - added extra regulatory checks for the EU: BLE legacy is an optional mode (not mandatory) and for WLAN modes an SSID is required. This only changes behavior if non-default radio parameters have been used. 20231023-1718 - bug fix: broadcast location data even if there is no GPS fix. Formally this is required by the Remote ID standards - bug fix: better random MAC address generation. When the DroneBeacon device gets powered up, it will generate a random MAC address (hardware ID that is included in the Bluetooth/WLAN signals). In this version, better random MAC address generation is used. This should prevent that multiple DroneBeacon devices use the same MAC address. In such cases says 5% of DroneBeacon devices had the same random MAC address when previous firmware versions were used. - bug fix: transmission rate. In previous versions, the data update rate was a bit too slow. Both the transmission interval and the number of transmissions have been optimized according to the Remote ID standards. - added an option in the configuration pages (radio section) to disable broadcasting the DroneBeacon name. Normally it will broadcast 'DroneBeacon_' and the last 4 characters of the serial number as BLE device name and as SSID (if those broadcast methods are enabled). 20230609-1341 - if WLAN broadcast is used, other 2.4 GHz WLAN channels are also allowed (and are compliant). - add option to enable (default) to disable responding to active WLAN scanning requests. If disabled, it will be much harder to be detected by smartphones 20230509-1209 - dropped GPS requirement of receiving at least 7 satellites introduced in 20230411-1543. 20230411-1543 - bug fix GPS lag up to 10 seconds (introduced in firmware 20230213-1330) - improved web interface, also useable with mobile devices - improved checking of EU rules - slow blinking if non-compliant mode is selected - select WLAN transmission channel (advanced) 20230213-1330 - bug fix, could not enter operator ID in webinterface - move to new buld tools - disable transmission in the dronebeacon is in config mode - bug fix, force battery leds to be on in config mode 20230125-1715 - firmware for db100, db120 and db121 transponders - bug fix sometimes the system time was incorrect when there is weak GPS reception 20221205-1525 - added support for db120 transponder - add transmit power setting in webinterface - set Remote ID classification based on selected region 20220923-1330 - added more functionality to the LED status in conformance with the FAA DoC requirements. LED status only flashes (status OK) if there is a GPS fix, a valid transmission mode is selected (configured region USA) and the internal tests do no show any error - bug fix in some rare case it was possible to change the SN number, if a cached version of the web interface was used. 20220907-1556 - more F3586−22 updates 20220822-1603 - send static messages with 1 Hz update rate (in order to be compliant with F3586−22) 20220818-1402 - bug fix GPS latitude longitude issues in case the transponder is in the West and/or South quadrant. - bug fix ASTM compliance NAN BSS ID (upgraded from v1.0 to 1.1 behaviour) - bug fix WiFi beacon rate, set to the selected update rate - bug fix WiFi NAN set the correct beacon interval parameter 20220720-1039 - first public release